Humidity Transmitters with Ethernet Interface

E+E Elektronik GmbH

"Humidity Transmitters with Ethernet Interface" by E+E Elektronik GmbH

Mar 8, 2018
The EE310 and EE360 industrial transmitters can now be integrated into a network via Ethernet interface.

Beside the RS485 interface with Modbus RTU protocol, the EE310 humidity and temperature transmitter and the EE360 moisture in oil transmitter from E+E Elektronik now feature an Ethernet interface with Modbus TCP protocol.

The EE310 and EE360 represent the latest generation of industrial transmitters from the Austrian sensor specialist E+E Elektronik. A multi-functional 3.5" TFT colour display provides a comprehensive overview of the measurement task and allows the user to perform all settings directly on the device. An integrated data logger stores up to 20,000 values per measurand.

Ethernet and RS485 Interfaces
As a standard, the measured data is available on two voltage or current outputs. The devices can be optionally fitted with an RS485 module with Modbus RTU protocol or with an Ethernet module with Modbus TCP protocol. The interface settings can be performed with a PC using the free configuration software or directly on the device via display and push buttons. The Ethernet module features Power over Ethernet (PoE) and an IP65 rated RJ45 connector. Both interface modules are available also for retrofitting.

EE310 Humidity and Temperature Transmitter
The EE310 measures relative humidity and temperature and calculates dew point temperature, frost point temperature, wet-bulb temperature, water vapour partial pressure, mixing ratio, absolute humidity and specific enthalpy. The transmitter is available for wall or duct mount, as well as with remote probes. The probes can be employed up to 180 °C (356 °F) and 20 bar (290 psi). Pluggable probe versions allow for quick and easy replacement.

EE360 Moisture in Oil Transmitter
The EE360 is dedicated for monitoring the moisture content in hydraulic, lubrication and insulation oils as well as diesel fuel. The device measures water activity (aw) and temperature (T), and calculates the absolute water content (x) in ppm. The stainless steel probe can be installed into the process with an ISO or NPT slide fitting, which facilitates the accurate control of the immersion depth. Using the optional ball valve, the probe can be mounted or removed even without process interruption.

Service-Friendly Design
The modular IP65 enclosure facilitates installation and maintenance. The active part of the device, which accommodates the electronics and the probe, can be replaced within seconds while the back cover and the electrical connection remain untouched.

More News

Sep 21, 2018
The IATF 16949 certification confirms that the Austrian sensor specialist meets the quality requirements of the automotive industry.
Aug 27, 2018
The EE650 air flow transmitter is now available with RS485 interface and Modbus RTU or BACnet MS/TP protocol.
Aug 9, 2018
The EE1900 humidity measurement module is optimised for climate and test chambers. The sensor copes well with pollution and chemical contamination.
Jul 18, 2018
The EE600 is a versatile, multi-range pressure transmitter for HVAC applications. It is fully config...
Mar 20, 2018
The EE310 and EE360 industrial transmitters can now be integrated into a network via Ethernet interf...
Address
Langwiesen 7
4209
Engerwitzdorf
Austria
Business Type
Manufacturer
Export Regions
Worldwide
Certificates
DIN EN ISO 9001
ISO/TS 16949:2002
DIN EN ISO 14001
IATF 16949:2016
Foundation
1979
Management
Josef Hart
Wolfgang Timelthaler
Employees
275

About E+E Elektronik GmbH

E+E Elektronik develops and produces sensors and transmitters for humidity, temperature, dew point, moisture in oil, air velocity, CO2, mass flow and pressure. Data loggers, hand-held measuring devices, humidity calibration systems and professional calibration services round off the comprehensive product range of the Austrian sensor specialist.

E+E Elektronik operates an accredited calibration laboratory in accordance with EN ISO/IEC 17025. As a designated laboratory (NMI), E+E Elektronik has been commissioned by the Austrian Federal Office for Metrology (BEV) to provide the national standard for relative air humidity and air velocity.

E+E Elektronik has subsidiaries in Germany, France, Italy, China, Korea and the USA and is well represented by a worldwide dealer network.