Catalog

WayCon Positionsmesstechnik GmbH

WayCon Positionsmesstechnik GmbH

  • ISO 9001:2015
  • REACH

WayCon Positionsmesstechnik GmbH

  • ISO 9001:2015
  • REACH

28.06.2017 00:06

Touch Displays WAY-AX and WAY-DX

The innovative touch display series WAY-AX and WAY-DX for the process control in the manufacturing of high quality products.

Better usability by a wide range of models.

Process Indicator WAY-AX
  • for two analog values or potentiometer input
  • applicable as flow meter, level meter, pressure meter etc.

Digital Indicator WAY-DX
  • for incremental encoder or sensor signals
  • applicable as counter, position meter, tachometer, frequency meter, speed meter etc.
  • additional functions e.g. timer, calculation of process time, reciprocal calculation

Better Visibility by a strong contrast & high resolution
Dot Matrix Display with 186 x 64 pixel
  • clear text explanations and commands are providing an intuitive menu structure
  • a wide range of units as well as any kind of symbols can be displayed

Three color LED-Backlight (green, yellow, red)
  • color can be adjusted easily by just one parameter
  • event depending color change, e. g. below limit, close limit, over limit

Better flexibility by touch & optional modules
Resistive Touch Panel with IP65 protection and enhanced temperature range (-20°C … 60°C)
  • Suitable for rough environmental conditions
  • Can be operated with any kind of working gloves, no limits on the used material
  • Maximum flexibility by modular design

WAY-AX
  • 2 analog inputs (16 bit), 3 control inputs
  • ±10 V / 0 … 20 mA / 4 … 20 mA
  • accurate 10 V reference output for potentiometers
  • mode for single, dual or cross calculated inputs
  • totalization, tare, average filter, etc. for each input
  • totalization of sum / difference of both inputs
  • linearization with 24 set points for each input

WAY-DX
  • 2 incremental inputs (HTL), 3 control inputs
  • for PNP, NPN or NAMUR sensors
  • up to 250 kHz
  • for speed, process time, timer, counter or velocity application
  • linearization with 24 set points
  • scaling, average filter, start up suppression

More News

The tried-and-tested LVDT series LV by WayCon is being expanded with the LV-G, which is equipped with rod end bearings. Thanks to the rod end bearings, the inductive sensors can be directly attached to the object to be measured. Here, the self-orienting rod end bearings facilitate the absorption of transverse force. Attachment via rod end bearings is ideal for installation at the end of a piston rod or the base of a hydraulic cylinder. Regular relubrication of the rod end bearings by the customer can also prolong the life and increase process safety.
With the IMX, WayCon Positionsmesstechnik offers a device that quickly converts input signals (position, frequency, SSI and speed) into absolute analog values. The analog variables of current and voltage can be scaled from 0/4 ... 20 mA and -10...+10 V respectively as desired.
Laser distance sensors of the LAS2-TM series impress with their high precision and their miniature housing.
Eddy current sensors of the EZ1000 series are designed for measurements under the toughest conditions and can be used in areas with explosion hazards. Thanks to the eddy current measuring principle, the measurement is contactless and is not affected by environmental influences such as water, dust or oil.

27.03.2021 01:05

Have you met TEDS?
TEDS (Transducer Electronic Data Sheet) plugs store sensor data like a conventional data sheet. Connected to a measuring amplifier, all required information about the sensor can be read out quickly, easily, and directly.
With a housing diameter of only 4 mm, the LVISM is one of the smallest LVDT sensors of its kind. Furthermore, with a length of 7 cm it is not even twice as long as a match.